Kilncae Pro-Fuser page GX solo dark background.jpg

THE PRO-FUSER

The Pro-fuser utilises Kilncare 2022 GX insulation system.

The step up from the Cub-Fuser, the Pro-Fuser has a much

larger chamber and a flat floor, allowing for easy loading on a

bigger scale than the smaller models.

The Pro-fuser has fantastic performance. Due to its high performance, infra-red quartz elements

and well designed insulation, like the Hobbyfuser 3, the Pro-fuser will also make the all important 700c to 800c dash at a rate of nearly 450 degrees per hour even with the optional shelf installed.

This makes the Pro-fuser almost infinitely controllable ensuring the glass doesn't get "over-worked" by it being in the heat longer than is required.

Take a look at the Pro-Fuser, alongside it's siblings, the Hobby-Fuser and Cub-Fuser, being describe by one of our agents, Warm Glass UK.

The KCR32C is multi-program controller designed for glass, ceramics & pottery use. It is targeted towards glass use with 32 programs each of up to 32 segments. Each segment is a controlled heating/cooling ramp followed by a soak. It is supplied pre-programmed with 9 typical glass programs and 9 typical ceramics programs (which can be over-written).

The slow rate capability of the KCR32C, down to 1c per hour, makes it the perfect controller for complicated glass cycles.

KCR32C Controller features:

32 programs - each with up to 32 segments.
Each segment is a controlled heating/cooling ramp soak.
Suitable for glass or ceramics use.
Soak times up to nearly 100 hours.
Ramp rates from 1 to 999°C/hour full.
Program Pause & Segment Advance facilities.
Can be held remotely, allowing for an easy and comfortable programming process.

Keyboard lockable.
Delayed start facility - up to 4 days.
Power failure recovery.
Energy used display.
Event / Damper / Fan relay output.
Alarm relay with alarm buzzer.
Mains power switch.
Built in the United Kingdom.

KCR32C WIFI Controller (Optional)

The KCR32CWIFi is internally the same as the KCR32C but has the capability to be accessed

and controlled remotely from your mobile device.

This is one of the most important advances in Kilncare kilns for many years.

Using Kilncares GATEway access site you can view how your kiln is running in real time. Stop the

firing or adjust programs all without even being in the same country let alone the same room.

The KCR32WIFI is also fitted with a USB port that allows programs to be entered that way direct from PC if required and also allows us to apply updates and run diagnostics without travelling to your kiln.

Internet access to view real time status and access data

The optional KCR32C WIFI allows the user to access the kiln in real time from anywhere with internet access via the Kilncare GATEway on our website. The benefits of this are obvious as there is no longer the need to travel to the studio or work place to see how the firing is proceeding or if indeed the firing is going as planned.

Also in the GATEway, which is unique to each user via password access, there is a firings library where past firings can be stored and named, a notes section and a log amongst other features.

Flat loading floor

The floor is flat with the entirety of the height of the kiln being in the chamber, which lifts out of the way when loading.

This type of floor is preferred by many glass artists.

The floor is low density, high insulation refractory bricks and can have the internal shelf kit placed onto it if desired or the glass can be fired directly onto the floor of the kiln providing a separator is used to protect the bricks.

Quartz Element Heating System

The heating system is in the roof only and utilises the latest technology "infra-red" quartz tube heating elements. This method is extremely hard wearing and strong, yet in the event of an element failure the tubes are both easy and cheap to replace.
The elements are switched off when the lid is opened by an automatic safety switch.

Fibre Lid

The kiln lid is made from stainless steel and lined out with non-ceramic fibre, This method of insulation removes the danger of brick dust or particles dropping onto the glass, so making for a very clean firing environment. It also makes the Pro-fuser incredibly resistant to shock damage.

The capability of the Pro-Fuser is due to the "super" backing insulation that makes the kiln ultra efficient and allows such a large capacity to be fired using so little power.

Fast Response Thermocouple.

The KCR32C gets its data from an ultra-fast response, stainless steel thermocouple meaning no lag between the kiln temperature and the KCR32Cs control.
The fact that the thermocouple is stainless steel means it is also resilient to accidental damage.

Angled Vent hole.

The front of the kiln has a large vent/peep hole which is closed using a spring assisted flap which houses our unique, anti-dust insulation pad which is taken from our larger fusing kiln models.
The vent/peep hole is angled so that the floor of the kiln and more importantly, your glass, can be seen.

Stainless Steel chamber and base

Following the trend of the rest of the Fuser range, the Pro-Fuser's chamber and base are stainless steel. This provides the kiln with a strong, resilient body that will be able to face the heat for much longer without the integrity of the metal becoming compromised due to rust.

Gas Spring Lid Assist

Lifting the lid on the Pro-fuser is aided by a specially designed gas spring that allows opening and closing of lid to be a single finger operation.

This makes the kiln completely user friendly but also helps in prolonged life due to the reduction of shock through "heavy" opening and closing of the lid.

Stainless Steel Lid Springs

Lifting the lid on the Pro-Fuser and is also aided by a pair of specially designed and built stainless steel lid springs on each side which allow opening and closing of lid to be a single finger operation.

This makes the kiln completely user friendly but also helps in prolonged life due to the reduction of shock through "heavy" opening and closing of the lid.

Optional Pro-Fuser Stand

The Pro-Fuser stand has two shelves, one for the kiln to sit on and one for your own use. It raises the kiln by 650mm to a comfortable height.
It is made of steel and is powder coated in our Ultra-marine blue.
The stand is supplied ready for assembly.

A further option for the Pro-Fuser stand is locking, swiveling wheels.

The wheels are pre-fitted at our factory, but the stand is still sent out ready for assembly.

Optional Inner Shelf Kit

Along with the purchase of the Pro-Fuser, there is also the optional extra shelf kit which includes a 48cmx82cm ceramic shelf, along with 5x 1inch posts.

Optional Wi-Fi capability

Also in the GATEway, which is unique to each user via password access, there is a firings library where past firings can be stored and named, a notes section and a log amongst other features.

4 Year Warranty

The Pro-Fuser comes with a HUGE 4 year warranty that applies for all parts (inc elements)! The fact that we are able to offer such a long warranty on these kilns just goes to show how well made they are and how they are truly built to last.

Made In The UK

The Pro-Fuser, along with all other Kilncare kilns, is made right here at Kilncare, in Stoke-on-Trent, United Kingdom.

Unrivalled aftercare

Here at Kilncare we really do pride ourselves on our customer service. We have a team of kiln experts at hand that will be there for you whenever you find yourself with any queries or worries who will do their absolute best to ensure that you can continue your glass journey as problem free as possible.

We really do go the extra mile when it comes to customer service, which you can see for yourself by taking a quick look at our online reviews.

MENU

THE PRO-FUSER

The Pro-fuser utilises Kilncare 2022 GX insulation system.